Skip to content
Lumber Calculator

Planning

Lumber Cut List Optimizer

Enter the pieces you need to cut. The optimizer chooses which 8–20 ft (or 2.4–5.4 m) boards to buy and how to cut each one. It allows for saw kerf and shows every board in a cutting diagram, so you buy less and waste less.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Lumber

Cuts

Finished lengths of one size. Make a separate list for each size (2×4, 2×6 …).

Stock boards

Stock lengths available

Untick lengths your yard does not carry; the optimizer only buys what is ticked.

Optimize for

Lowest cost uses the prices per length under “More options”.

More options
in

Width of the saw cut: about ⅛″ (3 mm) for a circular or miter saw.

in

Cut off to square checked or split factory ends.

Price per board

Leave empty to use the sample price. Your prices are saved on this device.

Plan

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How the cut list optimizer works

Turning a list of cuts into boards to buy is a cutting-stock problem. Each board has to hold its cuts plus one saw kerf between neighbouring cuts:

cut 1 + kerf + cut 2 + kerf + … + cut n  ≤  board length − end trim

The optimizer sorts your cuts from longest to shortest. It then fills one board at a time with whichever stock length leaves the smallest share as offcut. It repeats this for every combination of the stock lengths you ticked (up to 127 for seven lengths) and keeps the plan that best fits your goal:

  • Least waste: the least lumber left over as offcuts and sawdust.
  • Fewest boards: the fewest pieces to carry and handle, even if they are longer.
  • Lowest cost: the cheapest mix, using your price for each length. This helps when long boards cost more per foot.

Each board in the cutting diagram is drawn to scale. Identical boards are grouped (“× 3”), the dark lines are saw kerfs and the hatched end is the offcut.

Worked example: a 2×4 shelving unit

A garage shelf needs four 72″ uprights, eight 45″ shelf rails and eight 18″ cleats, all 2×4. That is 792″ (66 ft) of finished pieces. With a ⅛″ kerf:

PlanBoardsBoughtWaste
Naive: one piece per 8 ft board20 × 8 ft160 ft59%
Only 8 ft boards, packed9 × 8 ft72 ft8.3%
Optimized across 8–20 ft3 × 16 ft + 1 × 20 ft68 ft2.9%

The sample inputs above are this example. Untick lengths your yard doesn’t carry, or that won’t fit in your vehicle, and watch the plan change.

Why saw kerf matters

Every cut turns a strip of wood into sawdust as wide as the blade. Most circular and miter saw blades remove about ⅛″ (3 mm), thin-kerf blades about 3/32″ (2.4 mm), and a handsaw a little less. It sounds small, but it decides whether pieces fit:

  • Two 60″ pieces need 120⅛″, so they do not fit on a 10 ft (120″) board.
  • Two 47⅞″ pieces need 95⅞″, so they fit on an 8 ft (96″) board with ⅛″ to spare.

Factory ends are often checked, split or out of square. Set an end trim (½″ is common) to cut a clean end before measuring, and the optimizer will take it off every board.

Stock lengths and buying tips

MarketUsual stock lengths
US and Canada8, 10, 12, 14, 16, 18, 20 ft; studs also pre-cut at 92⅝″, 104⅝″, 116⅝″
Europe2.4, 3.0, 3.6, 4.2, 4.8, 5.4 m
Nordics2.4–5.4 m in 0.3 or 0.6 m steps
Japan1.82, 2.44, 3.0, 3.65, 4.0 m
  • Longer isn’t always cheaper. 16–20 ft boards often cost more per foot, and they are harder to haul and to find straight. Set your prices and choose “Lowest cost”.
  • Buy one or two spares. The plan assumes every board is usable, so add a spare for a bowed or split board. That matters most on long, visible pieces.
  • Cut the longest pieces first, from the straightest boards, and keep offcuts until the job is done.
  • For a whole wall, deck or shed, the project calculators (wall framing, framing takeoff, deck) already use this optimizer to choose plates, rims and rails. Price the result with the lumber cost calculator.

Common cut list mistakes

  • Mixing sizes in one list. A 2×4 and a 2×6 can’t share a board. Make one list per size, then add each to your lumber list.
  • Using nominal instead of finished lengths. Enter the length you will actually cut, including tenons, laps or extra for scribing.
  • Forgetting the kerf on tight fits, as in the 60″ example above.
  • Planning around lengths the yard doesn’t stock. Untick them so the plan only uses boards you can buy.

Frequently asked questions

How do I make a cut list for lumber?

List every finished piece of one size with its length and quantity. Enter them as rows, tick the stock lengths your yard sells and set your saw kerf. The optimizer shows how many boards of each length to buy and where to cut each one.

How many 36-inch pieces can I get from an 8 ft 2×4?

Two. With ⅛″ saw kerfs, three 36″ pieces would need 108¼″, more than the 96″ board. Two pieces use 72⅛″ and leave a 23⅞″ offcut.

How do I include the saw blade width?

Set the saw kerf under “More options”. It defaults to ⅛″ (3 mm), and the optimizer adds one kerf between neighbouring cuts on each board.

Is it cheaper to buy long boards and cut them down?

Sometimes. Long boards can pack cuts with less waste, but 16–20 ft lumber often costs more per foot. Enter the price of each length and choose “Lowest cost” to compare.

Does the optimizer find the perfect solution?

It uses a fast best-fit method and compares every combination of the lengths you ticked. That nearly always finds the minimum number of boards for project-sized lists, but it is not mathematically guaranteed. The note under the results says how many combinations it checked.

Can I use it for plywood sheets?

No. This tool cuts lengths (one dimension). For sheet counts, use the plywood calculator.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language