Skip to content
Lumber Calculator

Board feet & pricing

Lumber Weight Calculator

Find the weight of a single 2×4 or a whole truckload. Pick the species and moisture condition, add your sizes and lengths, and get the weight per piece, per foot and in total.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Wood

Moisture

Kiln-dried framing lumber ships near 15% moisture, kiln-dried hardwood near 7%. Green means freshly sawn; treated lumber is wet from the plant.

Pieces

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How lumber weight is calculated

Weight is simply the volume of wood times its density:

weight (lb) = actual thickness (in) × actual width (in) × length (in) ÷ 1,728 × density (lb/ft³)
weight (kg) = thickness (m) × width (m) × length (m) × density (kg/m³)

Use the actual size, not the nominal one: a 2×4 is 1½″ × 3½″, so a 2×4×8 holds 1.5 × 3.5 × 96 ÷ 1,728 = 0.29 cubic feet of wood. At 33 lb/ft³ (dry Douglas fir) that is about 9.7 lb. The calculator uses the dressed sizes of the market you pick, so metric sizes such as 45 × 95 mm work the same way.

Density depends mostly on the species and on how much water is still in the wood. Densities here start from typical air-dry values (about 12% moisture) after the USDA Forest Products Laboratory Wood Handbook.

Lumber weight chart: pounds per foot

Weight per linear foot of common US sizes. SPF, Douglas fir and southern yellow pine are air-dry (about 12% moisture); pressure-treated (PT) pine is wet from the treating plant, which is how it usually comes off the rack. Multiply by the length in feet for one board.

SizeSPFDouglas firSouthern pinePT pine (wet)
1×40.480.600.650.91
1×60.750.951.021.43
5/4×6 deck board1.001.261.361.91
2×40.961.211.301.82
2×61.501.902.042.86
2×81.982.502.693.77
2×102.533.193.434.81
2×123.073.884.175.85
4×42.232.813.034.25
4×63.514.424.766.68
6×65.516.957.4810.49

Pounds per foot. Densities used: SPF 26 lb/ft³, Douglas fir 33, southern pine 36, wet PT pine 50.

Weight of common boards

BoardSPFDouglas firSouthern pinePT pine (wet)
2×4 × 8 ft7.6 lb9.7 lb10.4 lb14.6 lb
2×6 × 8 ft12.0 lb15.2 lb16.3 lb22.9 lb
2×10 × 16 ft40.4 lb51.0 lb54.9 lb77.0 lb
2×12 × 16 ft49.2 lb62.0 lb66.7 lb93.6 lb
4×4 × 8 ft17.8 lb22.5 lb24.2 lb34.0 lb
6×6 × 8 ft44.1 lb55.6 lb59.8 lb83.9 lb

Green, air-dry and kiln-dried weight

Freshly sawn (“green”) wood can hold as much water as wood fibre, so it is far heavier than dry lumber. The calculator handles moisture like this:

  • Kiln-dried: softwood framing lumber stamped KD-19 is dried to 19% moisture or less and usually ships near 15%; kiln-dried hardwood is dried to about 7%. Below about 30% moisture, weight changes in step with the water, so density ≈ air-dry density × (1 + moisture) ÷ 1.12. Kiln-dried SPF comes out about 3% heavier than air-dry; kiln-dried oak about 4% lighter.
  • Air-dry (12%): the reference densities, typical of lumber that has sat indoors for a while.
  • Green: air-dry density times a green factor taken from the Wood Handbook green vs air-dry weights where the species matches — Douglas fir 43 vs 34 lb/ft³ (×1.26), western hemlock for hem-fir (×1.32), Engelmann spruce for spruce and SPF (×1.33), western red cedar (×1.17), redwood (×1.79). Other species use a typical ×1.4. Green weight varies a lot between boards, so treat it as a rough figure.

These are estimates. A moisture meter and a bathroom scale on one board will always beat any chart.

How much does pressure-treated lumber weigh?

Pressure-treated pine is soaked with a waterborne preservative under pressure, and it usually leaves the plant wet. That is why a treated 2×4 feels so much heavier than an untreated one. The calculator uses about 50 lb/ft³ (800 kg/m³) for wet treated southern pine — roughly 40% heavier than the same board dry. A wet PT 2×4×8 weighs about 14–15 lb and a 6×6×8 post about 84 lb.

Treated lumber loses that water over weeks or months in the open. Choose Air-dry or Kiln-dried for KDAT (kiln-dried after treatment) lumber or for boards that have dried out; the calculator then uses the untreated species density.

Hauling lumber: pickup loads

A common rule of thumb is that a ½-ton pickup carries about 1,000–1,500 lb of payload, but the real figure depends on the truck and its options — check the tire and loading sticker on the driver’s door jamb, and remember that passengers count toward payload. The calculator shows your load as a share of 1,500 lb and warns when it is more.

For scale: fifty 2×4×8 SPF studs weigh about 380 lb, but fifty wet PT 2×6×12s weigh about 1,700 lb — already more than many half-ton trucks should carry. For larger orders, ask the yard to deliver. To see what an order costs, use the MBF price calculator; for board feet, the board foot calculator.

Frequently asked questions

How much does a 2×4 weigh?

A kiln-dried 2×4×8 weighs about 8 lb in SPF, about 10 lb in Douglas fir and 10–11 lb in southern yellow pine. A wet pressure-treated 2×4×8 weighs about 14–15 lb.

How much does a 2×10 weigh?

A 2×10 weighs about 2.5–3.4 lb per foot dry, depending on species, so a 2×10×16 is roughly 40 lb in SPF and 55 lb in southern pine. Wet treated, it is about 77 lb.

How much does pressure-treated lumber weigh?

Wet from the plant, treated pine weighs about 50 lb per cubic foot — about 1.8 lb per foot for a 2×4 and 2.9 lb per foot for a 2×6. It gets lighter as it dries.

Is green lumber heavier than kiln-dried?

Yes. Green Douglas fir weighs about 43 lb per cubic foot against 34 lb air-dry, according to Wood Handbook figures — about 26% more. Some species, like redwood, are nearly twice as heavy green.

How much lumber can a half-ton pickup carry?

Rule of thumb: 1,000–1,500 lb of payload, including passengers — check your door-jamb sticker. That is roughly 130–190 kiln-dried 2×4×8 SPF studs, or 70–100 wet PT 2×4×8s.

How much does a board foot of lumber weigh?

An actual board foot (144 cubic inches) weighs density ÷ 12: about 2.2 lb for SPF, 2.8 lb for Douglas fir, 3.0 lb for southern pine and 4.2 lb for wet treated pine.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language