Skip to content
Lumber Calculator

Projects

House Lumber Calculator

A transparent ballpark for the framing lumber in a house: enter the floor area, stories and roof, and the calculator frames a simplified box house wall by wall — so you see where every board foot comes from, not just a per-square-foot guess.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

House

sq ft

All stories, measured outside the walls.

Stories

1 = square; 1.5–2 for most houses.

ft
Ground floor

Layout

Interior walls

Interior wall length per story as a share of the outside perimeter: 60%, 100% or 140%.

Roof

/ 12
in

Lumber price

Leave empty to use the sample price (editable in the lumber list below).

More options
in
in
in
%

Extra for bad boards, mistakes and offcuts.

Stock lengths available

Untick lengths your yard does not carry; the optimizer only buys what is ticked.

Plan

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How this estimate is built

This lumber calculator for house framing works from floor area — a square foot lumber calculator that estimates board feet, sheets and cost per square foot from a simplified framed house.

Many “lumber per square foot” numbers online are a single constant with no source. This calculator does not use one. It frames a simplified house with the same engines as the wall, floor and roof calculators and adds up the pieces:

  1. Footprint. Floor area ÷ stories gives the footprint; the shape ratio turns it into a rectangle (length = √(footprint × ratio)). A 2,000 sq ft single story at 1.6 : 1 is 56.6 × 35.4 ft.
  2. Exterior walls on every story: studs on center, 3-stud corners, double top plate, and your windows and doors with kings, jacks, headers and cripples. On a slab the bottom plates are treated.
  3. Interior walls — the biggest unknown in any house estimate — are set as a share of the perimeter (60%, 100% or 140%) and framed as cross walls spanning the inside width, with interior doors and two tee-backer studs where each one meets an exterior wall.
  4. Floors. Framed floors (a crawlspace or basement ground floor, and every upper floor) get rim joists, joists on center in bays no longer than 16 ft to a center beam, and subfloor sheets.
  5. Roof. A stick-framed gable: common rafters, fly rafters, ridge, collar ties, ceiling joists, gable studs, fascia and roof sheathing.

The result is a board-foot total you can trace part by part in the “Where the lumber goes” table and the lumber list. Change any assumption and see what it costs.

Example: lumber for a 2,000 sq ft house

A one-story, 2,000 sq ft house on a slab, 1.6 : 1 footprint, 8 ft walls (2×6 exterior, 2×4 interior, 16″ on center), typical interior walls, 10 windows, 8 interior and 2 exterior doors, a 6/12 roof with 2×8 rafters at 16″ and 2×6 ceiling joists, 7/16″ OSB walls and roof, 10% waste:

PartBoard feet
Exterior walls≈ 2,230
Interior walls≈ 1,410
Gable studs≈ 240
Roof framing≈ 5,520
Total≈ 9,400 (9.4 MBF)

That is about 4.7 board feet per square foot, plus 146 sheets of sheathing — roughly $9,800 at the sample prices, or about $4.90 per square foot. The same house on a framed floor (crawlspace) rises to about 12,900 board feet; as two stories of 1,000 sq ft each it takes about 10,500 board feet, because the second floor is framed but the roof is half the size.

HouseBoard feetSheetsSample cost
1,500 sq ft, 1 story, slab≈ 7,600119≈ $7,900
2,000 sq ft, 1 story, slab≈ 9,400146≈ $9,800
2,000 sq ft, 2 stories, slab≈ 10,500153≈ $11,500
2,500 sq ft, 2 stories, slab≈ 11,800183≈ $13,000

Prices are editable samples; enter your own price per MBF (or per m³) above.

What changes the number most

  • Roof framing. Stick-framed roofs with ceiling joists are the single largest block of lumber. Trusses replace the rafters, ridge and ceiling joists with factory-built units priced separately — the lumber total drops, but the truss quote must be added.
  • Framed floors. A crawlspace or basement adds a full floor system; each upper story adds another.
  • Interior walls. Open plans use far less wall than houses with many small rooms; try the three settings.
  • 2×6 vs 2×4 exterior walls. 2×6 walls hold more insulation and use about 50% more board feet per stud.
  • Stories and shape. A long, narrow footprint has more perimeter (more wall) for the same area than a square one.

Board feet, MBF and price

Lumber in the US is priced per thousand board feet (MBF). One board foot is 144 cubic inches of nominal size — a 2×4 that is 8 ft long holds 2 × 4 × 8 ÷ 12 = 5.33 board feet. The calculator prices every piece on its nominal board feet:

cost = board feet × price per MBF ÷ 1,000

At $780 per MBF, 9,400 board feet is about $7,300 of framing lumber before sheathing. Outside the US lumber is priced per cubic metre of actual size. See the board foot calculator to convert sizes, and use the wall framing, garage and shed calculators for detailed takeoffs.

Frequently asked questions

How much lumber does it take to build a 2,000 sq ft house?

A one-story 2,000 sq ft house on a slab with a stick-framed 6/12 roof comes to about 9,400 board feet (9.4 MBF) of framing lumber plus about 146 sheets of OSB in this estimate. A crawlspace floor raises it to about 12,900 board feet.

How many board feet of lumber per square foot of house?

This estimate lands around 4.7 board feet per square foot for a one-story slab house and about 6.5 with a framed floor. It varies with stories, roof type, wall size and how many interior walls you have, which is why the calculator builds it up instead of using one factor.

What does the lumber cost to frame a house?

At the sample price of $780 per MBF plus sample sheathing prices, the 2,000 sq ft example comes to roughly $9,800, about $4.90 per square foot. Enter your local price per MBF to update it.

Is this a substitute for a lumber takeoff?

No. It is a ballpark for budgeting and comparing options. For an order, have a takeoff made from your plans by your lumber yard or estimator.

Does the estimate include trusses?

No — the roof is stick-framed with rafters and ceiling joists. If you plan trusses, the rafter and ceiling joist lumber is replaced by trusses priced by the truss supplier.

Why is a two-story house not twice the lumber?

Two stories share one roof and one foundation. You add a second set of walls and a framed floor, but the roof covers half the area, so the total grows much less than the floor area.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language