Skip to content
Lumber Calculator

Framing

Framing Lumber Calculator

List the walls of your building — length, height, doors and windows — and get one framing takeoff: studs, plates, headers, jacks, cripples and sheathing, merged into a shopping list and broken down wall by wall.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Walls

Enter each wall as it is framed. On a rectangle, two walls run the full outside length and the other two fit between them (outside length minus two wall thicknesses). Window sizes are rough openings.

3D layout

Rectangle needs exactly four walls: 1 and 3 run through, 2 and 4 fit between them.

Framing

A closed rectangle has four three-stud corners — count one per wall.

%

Added once to the total of full-length studs (half the rate on sheathing).

More options
Top plate
in

About 82½″ (2,100 mm) for a standard 6′8″ door.

in

Subfloor to the bottom of the rough opening.

Fire blocking or nailers between studs.

Stock lengths available

Untick lengths your yard does not carry; the optimizer only buys what is ticked.

Loading 3D…

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How a framing takeoff works

Use this framing lumber calculator as a lumber calculator for framing a whole building: list every wall once and get one combined framing takeoff instead of adding up separate wall estimates.

A framing takeoff is the list of every stick of lumber a set of walls needs. Estimators build it wall by wall, then add the walls together into one order. This calculator does the same: each row is framed on its own and the results are merged.

For each wall:

layout studs  = ceil(wall length ÷ spacing) + 1
corner studs  = 2 per three-stud corner
openings      = 2 king studs + 2 or more jacks + header + cripples (+ rough sill for windows)
plates        = wall length × 3 (one bottom plate, double top plate)

Layout studs that fall inside a door or window are left out, because the king and jack studs replace them. Studs are cut to the wall height minus the three plates; for 8, 9 and 10 ft walls the calculator buys pre-cut studs (92⅝″, 104⅝″ and 116⅝″). Jacks, cripples and blocking are cut from full-length boards, and the cut optimizer picks the stock lengths that waste the least.

Then the walls are added up. The Shopping list tab merges identical pieces — every 2×4 × 92⅝″ from every wall becomes one line — and the By part tab shows what each wall needs, so you can stage the lumber where it will be used.

Worked example: a 16 × 12 ft building

The calculator opens with a 16 × 12 ft building with 8 ft walls, 2×4 studs at 16″ on center, a double top plate, one door and four 36 × 48″ windows. Walls 1 and 3 are 16 ft long and run through; walls 2 and 4 fit between them at 12 ft minus two 3½″ walls = 11′ 5″.

WallLengthOpeningsLayout + corner + king studs
116′1 door, 1 window9 + 2 + 4 = 15
211′ 5″1 window7 + 2 + 2 = 11
316′2 windows9 + 2 + 4 = 15
411′ 5″—10 + 2 + 0 = 12

That is 53 full-length studs; with 10% waste the order is 59 pre-cut 92⅝″ studs. The five openings add 10 jack studs, 26 cripples and 10 header plies. Plates are 3 × 54.8 ft ≈ 165 linear feet, and the walls take 14 sheets of 4×8 sheathing, 15 with waste. At the editable sample prices the lumber and sheathing come to roughly $690.

The quick check — about one stud per linear foot of wall — gives 55 for 54.8 ft of wall, close to the detailed count before waste.

Measuring walls and corners

The most common takeoff mistake is counting the corners twice. When four walls make a rectangle, two of them run through (full outside length) and two butt between them, so the butt walls are shorter by two wall thicknesses:

Wall2×4 wall (3½″)2×6 wall (5½″)
Through walloutside lengthoutside length
Butt walloutside length − 7″outside length − 11″

Each corner needs extra studs so both walls have something to nail to and the drywall has backing. A traditional three-stud corner adds 2 studs; a ladder or California corner adds less. Set Corners per wall to one corner for a closed rectangle — four walls, four corners. Interior walls that tee into another wall need a tee (one or two extra studs or ladder blocking) in the wall they meet; add those with the wall framing calculator when you need them exactly.

Buying framing lumber

  • Studs. Pre-cut studs (92⅝″ for 8 ft walls) save a cut per stud. Stud-grade or No. 2 SPF, Douglas fir or southern pine are all common for walls.
  • Plates. Buy the longest straight boards you can carry: fewer splices, and top-plate joints must be offset from each other. The optimizer splits long walls into the fewest equal pieces.
  • Bottom plates on concrete must be pressure-treated (tick the option and they are listed as treated lumber).
  • Headers. This calculator counts header lumber but does not size headers. Header size depends on the opening width and the loads above — use your code's header tables (for example IRC Table R602.7(1) in the US) or ask your building department.
  • Waste. 10–15% is the usual allowance for framing. Here it is added once to the project total, so a ten-wall house does not get ten rounded-up extras.

Prices in the lumber list are editable samples. Enter your yard's prices, then use Add to lumber list to combine this takeoff with the floor from the joist calculator, the roof from the rafter calculator and extra sheet goods from the plywood calculator.

Common framing takeoff mistakes

  1. Using outside dimensions for every wall. Four walls at the full outside length double-count every corner — about 14″ of extra plate and a stud or two per corner.
  2. Forgetting the double top plate. Load-bearing walls need three plate runs, not two.
  3. Ignoring openings. A window does not save studs: it swaps one or two layout studs for two kings, two jacks, cripples above and below, a sill and a header.
  4. Subtracting window areas from sheathing. Walls are sheathed over and the openings cut out afterwards, so the offcuts rarely get reused.
  5. Adding waste wall by wall. Rounding up each wall separately inflates the order; apply the allowance once to the total.

Frequently asked questions

How much lumber do I need to frame a 16 × 12 building?

With 8 ft walls, 2×4 studs at 16″ on center, one door and four windows, plan on about 59 pre-cut studs (53 plus 10% waste), 36 jacks and cripples cut from 2×4 stock, about 165 linear feet of plate and 15 sheets of 4×8 sheathing. Your own doors and windows change the count — enter them above.

How do you do a framing takeoff?

Measure each wall as it will be framed, count layout studs (length ÷ spacing + 1), add corner and tee studs, frame every opening with kings, jacks, a header and cripples, take three plate runs per wall, then add the walls together and apply 10–15% waste once.

How many studs per linear foot of wall?

At 16″ on center, about one stud per linear foot of wall once corners and openings are included. At 24″ on center it is closer to three studs per four feet. Use it as a cross-check; the wall-by-wall count is more accurate.

Do I measure walls inside or outside?

Use the length each wall is framed. On a rectangle, two walls run the full outside length and the other two fit between them, so they are the outside length minus two wall thicknesses (7″ for 2×4 walls, 11″ for 2×6 walls).

How much waste should I add to framing lumber?

10% is a common allowance for studs and 5% for sheathing; 15% if you expect a lot of bowed or split boards. This calculator applies the percentage once to the project total, not to each wall.

Does this include the floor and roof?

No — it covers walls. Use the joist calculator for floors and the rafter calculator for roofs, add each one to your lumber list, and the list merges everything into one order.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language