Skip to content
Lumber Calculator

Projects

Shed Lumber Calculator

Pick a shed size, roof and floor, and get every skid, joist, stud, plate, header, rafter and sheet — framed the way a builder lays it out, shown in 3D and priced as one order list you can take to the yard.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Shed

ft

Gable end — the roof spans this way.

ft

Along the ridge.

ft

8 ft walls use 92⅝″ pre-cut studs.

Door in

Roof

Roof style
/ 12

Rise in inches per 12″ of run.

in
in

Floor

Foundation

Door & windows

in
in
in
in
in

From the floor to the bottom of the rough opening.

Use rough opening sizes. The door goes in the front wall; windows go on the side walls first. Set the door width to 0 for no door.

Walls & sheathing

More options
Top plate

Two plies over each opening.

%

Extra for bad boards, mistakes and offcuts.

Stock lengths available

Untick lengths your yard does not carry; the optimizer only buys what is ticked.

Loading 3D…

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How the shed material list is built

This lumber calculator for shed builds is a full shed lumber calculator: floor, walls, roof, sheathing and siding in one shed material list you can price and take to the yard.

Most shed calculators multiply the floor area by a factor. This one frames the shed piece by piece, the same way you would on site, and adds everything up into one order list:

  1. Floor — pressure-treated skids, a rim joist on each side and floor joists on center, spanning the short way. Floor sheathing is laid with the long edge across the joists and the rows staggered.
  2. Walls — the front and back walls run the full length of the shed and the side walls fit between them, so a side wall is the shed width minus two wall thicknesses (7″ with 2×4s). Each through wall gets a 3-stud corner at both ends. The door and windows get king studs, jack studs, a two-ply header, cripples and a rough sill.
  3. Gables — gable studs fill the triangles at both ends, on the same spacing as the wall studs.
  4. Roof — common rafters on layout, fly rafters for the rake overhang, a ridge board one size deeper than the rafters, collar ties and fascia.
  5. Sheathing — siding or wall sheathing for the four walls plus the gable triangles, and roof sheathing for both slopes including the overhangs.

Every piece is matched to a stock length your yard sells, short pieces such as jacks and cripples are cut from shared boards, and long plates are spliced. Tap a row in the lumber list to highlight those pieces in the 3D model, or switch layers off to look inside.

Worked example: lumber list for a 10×12 shed

A 10 × 12 ft gable shed with 8 ft walls (2×4 studs at 16″ on center, double top plate), a 6/12 roof with 2×6 rafters at 24″, 12″ eaves and 6″ rakes, a floor of 2×6 joists at 16″ on three 4×6 skids, a 48″ × 78″ door in the long wall, one 24″ × 36″ window, T1-11 siding and 7/16″ OSB on the roof. With 10% waste the calculator lists:

PartMaterialQty
Floor2×6 × 10′ treated joists11
Floor2×6 × 12′ treated rim joists2
Floor4×6 × 12′ treated skids3
Floor23/32″ T&G subfloor 4×85
Walls2×4 × 92⅝″ pre-cut studs48
Walls2×4 plates (8′–20′)10
Walls2×4 for jacks, cripples and sill6
Walls2×8 headers (8′ and 10′)2
Gables2×4 gable studs2
Roof2×6 × 8′ rafters20
Roof2×8 × 14′ ridge, 2×6 collar ties and fascia4
SheathingT1-11 siding 4×814
Sheathing7/16″ OSB 4×8 roof9

That is 108 pieces of lumber (about 850 board feet) and 28 sheets, or roughly $1,800 at the sample prices — about $15 per square foot of floor. Prices are editable samples; enter your yard’s prices and the totals update. Roofing, trim, hardware and fasteners are not included.

Shed floor: skids or a slab

A wood floor on skids is the classic shed foundation: two to four 4×4 or 4×6 skids sit on gravel or blocks, and the floor frame sits on the skids. Everything in contact with the ground — and in most sheds the whole floor frame — should be pressure-treated lumber rated for ground contact. The calculator lists the skids, rims and joists as treated.

On a concrete slab there is no floor framing. The walls stand on the slab, and the bottom plates must be pressure-treated (or separated from the concrete). Choose “Concrete slab” and the floor drops out of the list.

Floor joists span the short way. A 2×6 at 16″ on center is the usual choice for 8–10 ft wide sheds; heavier loads (riding mowers, workshops) or wider sheds call for 2×8s or closer spacing. This calculator counts lumber — check joist spans with a span table or your local building code.

Gable or lean-to roof, pitch and rafter length

A gable roof has two slopes meeting at a ridge. The rafter length follows from the run and the pitch:

run = width ÷ 2 − ridge thickness ÷ 2
rafter = run ÷ cos(pitch angle) + eave overhang ÷ cos(pitch angle)

For a 10 ft wide shed at 6/12 that is 59¼″ ÷ 0.894 + 12″ ÷ 0.894 ≈ 80″ — an 8 ft rafter. A lean-to (shed roof) has one slope from a tall front wall to a low back wall; the rafters span the full width, so they are longer, and the tall wall is taller by the rise (a 10 ft wide lean-to at 2/12 rises 20″).

PitchAngleSlope factorRise over a 10 ft gable
3/1214.0°1.03115″
4/1218.4°1.05420″
6/1226.6°1.11830″
8/1233.7°1.20240″
12/1245.0°1.41460″

Rafters at 24″ on center are typical for small sheds with OSB roof sheathing; use 16″ for heavy snow or thin sheathing. Rafter size depends on span, spacing and snow load — check the rafter span tables in your building code.

Buying tips and common mistakes

  • Buy pre-cut studs for 8 ft walls: 92⅝″ studs with a single bottom and double top plate give a 97⅛″ wall with no cutting. For other heights the calculator cuts studs from the next longer stock length.
  • Don’t forget the corners. The rule of thumb “one stud per foot of wall” is close for a plain shed, but corners, door and window framing add up. The calculator counts them individually.
  • Side walls are shorter than the shed. Plates for the side walls are the width minus two wall thicknesses; ordering two full-width plates per side wastes little, but cutting them full length is a common layout mistake.
  • Treated where it touches the ground. Skids, floor framing and plates on concrete should be treated; walls and roof framing can be standard framing lumber.
  • Add waste. 10% covers crooked boards and miscuts on framing; sheets get half the waste because offcuts are reused.
  • What is not included: roofing (shingles or metal), drip edge, trim boards, door slabs, hardware, nails and screws.

For a bigger building use the garage lumber calculator; for a single wall, the wall framing calculator. Add the list to your lumber list to combine it with other projects.

Frequently asked questions

How much lumber do I need for a 10×12 shed?

With 8 ft walls at 16″ on center, a 6/12 gable roof with 2×6 rafters at 24″ and a floor on three 4×6 skids, a 10×12 shed takes about 108 pieces of lumber (roughly 850 board feet), 5 subfloor sheets, 14 siding panels and 9 roof sheets, including 10% waste.

How many 2×4s do I need for a 10×12 shed?

About 66 2×4s: 48 pre-cut studs (including corners, king studs and waste), 10 plates, 6 boards for jacks, cripples and the window sill, and 2 for the gable studs — with one door and one window.

How much lumber for a 12×16 shed?

With the same defaults, a 12×16 shed needs about 130 pieces of lumber (around 1,090 board feet), including 78 2×4s and 22 rafters, plus 35 sheets of subfloor, siding and roof sheathing.

How much does the lumber for a shed cost?

At the sample prices, framing and sheathing for a 10×12 shed come to about $1,800 — roughly $15 per square foot of floor — and a 12×16 to about $2,300. Siding is the largest single item. Enter your local prices to get your own total.

Should shed floor joists be 16 or 24 inches on center?

16″ on center is the usual choice for shed floors because it keeps ¾″ floor sheathing stiff under heavy equipment. 24″ on center can work with thicker sheathing and light loads.

Does a shed on skids need pressure-treated lumber?

Yes. Skids sit on the ground and the floor frame sits close to it, so both should be pressure-treated lumber rated for ground contact. The walls and roof can be standard framing lumber.

How long should shed rafters be?

For a 10 ft wide gable shed at 6/12 with a 12″ overhang, each rafter is about 6 ft 9 in before cutting, so you buy 8 ft boards. Wider sheds, steeper pitches and longer overhangs need longer rafters — the calculator picks the stock length for you.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language