Skip to content
Lumber Calculator

Projects

Garage Lumber Calculator

Enter the garage size, doors and roof to get every stud, plate, header, rafter, ceiling joist and sheet for a slab-on-grade garage — framed piece by piece, shown in 3D and priced as one list.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Garage

ft

The front wall with the garage doors.

ft
ft

9 ft walls use 104⅝″ pre-cut studs and leave room for a 7 ft door and header.

Garage doors

ft
ft

Rough opening sizes. Single doors are usually 8–10 ft wide, doubles 16–18 ft, 7–8 ft high.

Service door & windows

in
in
in
in
in

Roof

Roof framing
/ 12

Rise in inches per 12″ of run.

in
in

Walls & sheathing

Used for every opening, two plies. Wide garage doors often need an engineered beam — check your code tables.

More options
Top plate
%

Extra for bad boards, mistakes and offcuts.

Stock lengths available

Untick lengths your yard does not carry; the optimizer only buys what is ticked.

Loading 3D…

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How the garage takeoff is calculated

This lumber calculator for garage framing covers the whole building — walls, garage-door headers, rafters or trusses and sheathing — so you get one garage lumber list instead of a stud count.

The calculator frames a slab-on-grade garage the way a crew would and lists every piece:

  • Walls — the front and back walls run the full width, the side walls fit between them, and each corner gets a 3-stud corner. Studs are on center from the corner; each garage door, the service door and every window get king studs, jack studs (two per side on openings wider than 6 ft), a two-ply header and cripples. Bottom plates on the slab are pressure-treated.
  • Roof — the roof spans the short side of the building. With rafters you get common rafters, fly rafters at the rakes, a ridge board one size deeper than the rafters, collar ties, ceiling joists that tie the walls together, gable studs and fascia. With trusses, the trusses are counted as items at 24″ on center and the lumber list keeps the fascia and fly rafters.
  • Sheathing — wall sheathing around all four walls plus the gable triangles (whole sheets saved by the garage door are deducted), and roof sheathing for both slopes including the overhangs.

Every piece is matched to the stock lengths your yard carries, long plates are spliced, and short pieces share boards. The shed lumber calculator uses the same engine for smaller buildings with a wood floor.

Worked example: how much lumber for a 24×24 garage

A 24 × 24 ft garage with 9 ft walls (2×4 at 16″ on center, double top plate), one 16 × 7 ft garage door, a 36″ service door, two 36″ × 36″ windows, 2×12 headers, a 4/12 roof with 2×8 rafters at 16″ and 2×6 ceiling joists, 12″ eaves and 6″ rakes, and 7/16″ OSB on walls and roof. With 10% waste:

PartMaterialQty
Walls2×4 × 104⅝″ pre-cut studs80
Walls2×4 × 12′ plates (bottom plates treated)24
Walls2×4 for jacks, cripples and sills11
Walls2×12 headers (8′–18′)4
Gables2×4 gable studs5
Roof2×8 × 14′ rafters47
Roof2×6 × 12′ ceiling joists38
Roof2×10 ridge, 2×8 collar ties and fascia11
Sheathing7/16″ OSB 4×8 — walls and gables34
Sheathing7/16″ OSB 4×8 — roof24

That is 220 pieces of lumber (about 2,500 board feet, 2.5 MBF) and 58 sheets — roughly $2,900 at the sample prices, or about $5 per square foot of floor. Switching to trusses drops the rafters, ridge, collar ties, ceiling joists and gable studs and adds 13 trusses; the lumber falls to about 940 board feet. Prices are editable samples.

Garage door headers

The header over a garage door carries the roof (and any snow) across a wide opening, so it is the one part of a garage you should not guess. The calculator uses the header size you pick for every opening and frames it as two plies on edge with two jack studs per side on openings over 6 ft.

A single 8–9 ft door on a one-story garage can often be spanned with doubled 2×10s or 2×12s; a 16 ft double door usually needs an engineered beam (LVL, PSL or glulam) or a much deeper built-up header. Size headers from the header tables in your building code (in the US, IRC Table R602.7(1)) or from your lumber supplier, and check your local code — snow load and building width change the answer.

Walls also need room for the door: a 7 ft door plus a 2×12 header is 95¼″, which does not fit under the 92⅝″ studs of an 8 ft wall. That is why garages are often framed with 9 or 10 ft walls.

Rafters or trusses?

Most new garages use pre-built trusses: they span the full width without interior bearing walls, go up fast and are engineered for your loads. They are ordered from a truss plant, typically at 24″ on center, so a 24 ft long garage takes 288 ÷ 24 + 1 = 13 trusses including the two gable-end trusses.

Stick framing with rafters and ceiling joists is common for smaller garages, for a usable attic, or when trusses are hard to get. Rafters sit on the wall plates against a ridge board; ceiling joists (rafter ties) at plate height keep the walls from spreading, and collar ties brace the upper third. Rafter length at 4/12 over a 24 ft span is about 12 ft 7 in plus the overhang, so 14 ft boards.

GarageTrusses at 24″Rafters at 16″ (incl. fly)
20 × 201136
24 × 241342
30 × 40 (ridge along 40 ft)2166

Buying tips and common mistakes

  • Treated bottom plates. Every plate on the slab must be pressure-treated (or separated from the concrete by an approved barrier) and anchored with bolts or straps.
  • Long walls are spliced. A 24 ft plate comes from two 12-footers; stagger the splices in the top plates by at least 24″.
  • Check the rafter size. Rafter and ceiling joist sizes depend on span, spacing, snow load and species — use the span tables in your building code or the rafter calculator.
  • Waste. 10% on framing is typical; sheets get half the waste because offcuts are reused.
  • Not included: slab and footings, garage doors, roofing, house wrap, siding, trim and fasteners.

Need just one wall? Use the wall framing calculator. Add the whole list to your lumber list to combine it with other projects.

Frequently asked questions

How much lumber do I need for a 24×24 garage?

With 9 ft 2×4 walls at 16″, one 16 ft door, a 4/12 roof of 2×8 rafters at 16″ and 2×6 ceiling joists, a 24×24 garage takes about 220 pieces of lumber (roughly 2,500 board feet) and 58 sheets of OSB, including 10% waste.

How many 2×4s do I need to frame a 24×24 garage?

About 120 2×4s for the walls and gables: 80 pre-cut studs (including corners, king studs and waste), 24 plates and the rest for jacks, cripples, sills and gable studs.

What does the lumber for a 30×40 garage cost?

With two 9 ft doors and stick framing, a 30×40 garage takes about 4,500 board feet of lumber and 102 sheets — roughly $5,100 at the sample prices. Enter your local prices to get your own number.

How many trusses do I need for a 24×24 garage?

13 trusses at 24″ on center: 24 ft × 12 ÷ 24 = 12 spaces, plus one. That count includes the two gable-end trusses.

What size header do I need for a 16 ft garage door?

It depends on the roof load, snow load and building width, so it must come from your code’s header tables or an engineered beam supplier. A 16 ft opening usually needs an LVL, glulam or a deep built-up header — check your local building code.

Should garage walls be 8 or 9 feet high?

9 ft walls are common because a 7 ft door plus its header does not fit under an 8 ft wall’s 92⅝″ studs. Taller doors, a car lift or storage call for 10 ft walls or more.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language