Skip to content
Lumber Calculator

Framing

Plywood Calculator

Add the walls, floors and roof slopes you need to cover and get the number of plywood or OSB sheets — laid out the way they go on, with staggered joints, area, weight and cost.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Areas to cover

Quantity repeats identical areas — 2 for both slopes of a gable roof. Roof slopes are measured along the rafter, overhang included. Walls can be entered one by one or as the whole perimeter.

Sheets

Sheet size
in
in
in

In your market currency.

Long edge of the sheets

Auto: floors and roofs run the long edge across the joists or rafters; walls stand sheets up when the wall is no taller than a sheet.

%

For damaged sheets and mistakes — cutting waste is already in the layout count.

Plan

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How many sheets of plywood do I need?

The quick answer divides the area by the area of one sheet. A 4×8 sheet covers 32 sq ft (a 2500 × 1250 mm sheet covers 3.125 m²):

sheets ≈ area ÷ 32 sq ft × (1 + waste)

That is the theoretical minimum, and it is often one or two sheets short, because sheets have to be cut to fit and the pieces are not always reusable. This calculator lays the sheets out in courses the way they are installed:

sheets per course = length ÷ sheet length
full courses      = width ÷ sheet width, rounded down
last course       = the leftover strip; one sheet gives as many strips as fit
sheets            = full courses × sheets per course + last course, rounded up

The offcut at the end of one course starts the next course, which also staggers the joints. Both numbers are shown: the layout count in the headline and the pure area count underneath.

Worked example: floor, walls and roof of a 16 × 12 building

The calculator opens with a small 16 × 12 ft building and 7/16″ OSB:

AreaSizeLayoutSheets
Floor16 × 12 ft = 192 sq ft2 per course × 3 courses6
Walls56 × 8 ft = 448 sq ft, 60 sq ft of openings14 sheets standing up, 1 whole sheet of openings deducted13
Roof (2 slopes)16 ft × 7′ 10″ each2 per course × 2 courses, per slope8

That is 27 sheets, 29 with 5% waste, for about 831 sq ft — the area alone would suggest 26. In practice the floor gets a thicker tongue-and-groove subfloor panel, so run the floor separately with that product selected, or add each result to your lumber list.

Measuring walls, floors and roofs

  • Walls: length × height. Enter each wall, or the whole perimeter in one row. With 8 ft walls and 4×8 sheets standing up, each 4 ft of wall is one sheet. Taller walls are sheathed horizontally with a strip at the top.
  • Floors: outside length × width. Sheets run with the long edge across the joists and the end joints staggered by at least one joist bay.
  • Roofs: for each slope, the length along the ridge (rake overhangs included) × the length from the eave edge to the ridge measured along the rafter. Enter 2 as quantity for a gable roof. The rafter calculator gives the slope length from the pitch.
  • Gable ends: a triangle is half of width × height — enter it as an "other area" with half the height, or as a rectangle to include the cut-off waste.

Plywood, OSB and subfloor: which sheet?

UseCommon US productCommon metric product
Wall sheathing7/16″ OSB or ½″ CDX plywoodOSB/3 12–15 mm
Roof sheathing7/16″ OSB or ½″–⅝″ plywoodOSB/3 15–18 mm or plywood 18 mm
Subfloor23/32″ (¾″) tongue-and-grooveOSB/3 18–22 mm T&G

The thickness you need depends on the joist or rafter spacing and the loads. Structural panels carry a span rating stamp — check it against your framing spacing and your building code. Weight is estimated at about 600 kg/m³ for wood panels, so a ½″ 4×8 sheet weighs around 50 lb; real panels vary with species and moisture. Prices are editable samples.

Tips to waste fewer sheets

  1. Start courses with full sheets and reuse the offcut at the start of the next course.
  2. On walls, sheath right over doors and windows and cut them out with a router afterwards — faster and stronger than piecing around them.
  3. Rip narrow strips for the last course from shared sheets: one sheet gives two 2 ft strips or four 1 ft strips.
  4. Leave the recommended expansion gap between panels (often ⅛″ / 3 mm) — the layout does not reduce coverage for it.
  5. Order one or two extra sheets for damaged edges; this calculator adds the waste percentage once to the total.

Frequently asked questions

How many sheets of plywood do I need for a 12 × 12 room floor?

144 sq ft ÷ 32 = 4.5 sheets by area. Laid out, the 12 ft length takes 1.5 sheets per course and three 4 ft courses, so 4.5 → 5 sheets, plus waste — order 5 or 6.

How many sheets of OSB for a 12 × 8 wall?

Three 4×8 sheets standing up cover a 12 ft wall 8 ft tall. Do not subtract a window; sheath over it and cut it out.

How many square feet are in a sheet of plywood?

A 4×8 sheet is 32 sq ft; 4×9 is 36 sq ft and 4×10 is 40 sq ft. A metric 2500 × 1250 mm sheet is 3.125 m², and 2440 × 1220 mm is 2.98 m².

How do I calculate roof sheathing?

For each slope, multiply the length along the ridge by the slope length from eave to ridge (overhang included), add the slopes and divide by the sheet area — or enter each slope above, quantity 2 for a gable roof, to get the layout count.

How much waste should I add for plywood?

When sheets are counted by layout, 5% covers damaged sheets and mistakes. If you only divide area by 32, add 10–15% to cover the cuts.

How much does a sheet of plywood weigh?

Roughly 40–60 lb for a ½″ to ¾″ 4×8 sheet, depending on species and moisture; this calculator estimates about 50 lb for ½″ and 75 lb for ¾″.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language