Skip to content
Lumber Calculator

Framing

Wall Framing Calculator

Enter the wall length, height and openings to get every stud, plate, header and cripple — laid out on 16″ or 24″ centers, shown in 3D, and turned into a lumber list you can take to the yard.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Wall

ft
ft

Enter 8, 9 or 10 ft for standard walls with pre-cut studs (92⅝″, 104⅝″, 116⅝″).

Doors & windows

Use rough opening sizes from the door or window maker. Remove every row for a plain wall.

More options
Top plate

Fire blocking or nailers between studs.

%

Extra for bad boards, mistakes and offcuts.

Stock lengths available

Untick lengths your yard does not carry; the optimizer only buys what is ticked.

Loading 3D…

Results

Lumber list

Enter your dimensions to see the lumber list.

Estimate — check sizes and quantities with your lumber yard.

Results

How many studs do I need?

This is a lumber calculator for wall framing: a wall lumber calculator that counts studs, plates, headers, jacks and cripples for one wall, with doors and windows framed the way a carpenter would.

For a plain wall, the quick rule is one stud for every 16 inches of wall, plus one:

studs = wall length (in) ÷ spacing (in) + 1

A 12-foot wall at 16″ on center needs 144 ÷ 16 + 1 = 10 studs; at 24″ on center it needs 7. A faster field estimate is one stud per linear foot of wall, which already covers corners, openings and a few culls on most houses.

Real walls need more than the layout studs:

  • Corners — a standard three-stud corner adds 2 studs to the wall that runs through. A ladder or tee intersection adds 1.
  • Each door or window — 2 king studs, 2 or more jack (trimmer) studs, a header, cripple studs above the header and, for windows, a rough sill with cripples below. Layout studs inside the opening are left out.
  • Waste — add about 10% for bowed, twisted or split studs.

The calculator lays out the wall the way a framer does — from the start of the wall, on center — so every stud, king, jack and cripple is counted where it actually goes. Toggle to 3D to check it, or tap a row in the lumber list to highlight those pieces.

Top and bottom plates

Every wall has a bottom (sole) plate and a top plate. Load-bearing walls normally get a double top plate that laps at corners and ties walls together, so you buy three times the wall length in plate stock. Plates longer than the longest board you can buy are spliced; the calculator splits each run into the fewest equal pieces and picks the stock lengths with the least waste. Joints in the top plates should be offset by at least 24 inches.

A bottom plate that sits on a concrete slab or foundation must be pressure-treated. Tick the option and the bottom plate is listed as treated lumber.

Stud length and pre-cut studs

The stud length is the wall height minus the plates. With a single bottom plate and a double top plate (three 1½″ plates), an 8-foot wall is framed with 92⅝″ pre-cut studs, giving a 97⅛″ wall that fits 8-foot drywall plus the ceiling. Nine- and ten-foot walls use 104⅝″ and 116⅝″ pre-cuts. Enter 8, 9 or 10 feet and the calculator buys pre-cut studs; any other height is cut from the next longer stock length.

WallPre-cut studFramed height
8 ft92⅝″97⅛″
9 ft104⅝″109⅛″
10 ft116⅝″121⅛″

Headers, jacks and cripples

A header carries the load over an opening onto the jack studs. On a 2×6 wall a header is usually two plies of 2× lumber on edge; on a 2×4 wall the plies are separated by a ½″ spacer to make the 3½″ wall thickness. The header length is the rough opening width plus the jack studs on both sides.

This calculator counts the lumber; it does not size headers. Header size depends on the opening width, the roof and floor loads above, snow load and building width — use the header tables in your building code (for example IRC Table R602.7(1) in the US) or ask your building department. Openings wider than 6 feet get two jack studs per side here, which many code tables require.

Sheathing sheets

Sheathing is counted by laying full sheets over the wall, vertically when the wall is no taller than a sheet and horizontally otherwise. Openings are sheathed over and cut out, so they are not subtracted. A 12 × 8 ft wall takes three 4×8 sheets. Half of the waste allowance is applied to sheets. For whole houses, use the plywood and sheathing calculator.

Frequently asked questions

How many 2×4s do I need for a 10-foot wall?

At 16″ on center a 10-foot wall needs 9 layout studs (120 ÷ 16 = 7.5, rounded up to 8, plus 1), plus three 10-foot plates (or two 10-footers and a third for the double top plate). Add 2 studs for each corner and about 10% for waste — with two corners, roughly 15 studs and 3 plates.

How many studs for a 12-foot wall?

10 studs at 16″ on center, 7 at 24″ on center — before corners, openings and waste. With two corners and 10% waste, plan on about 16 studs at 16″ centers.

Are studs 16 or 24 inches on center?

Most US walls are framed 16″ on center. 24″ on center (“advanced framing”) uses fewer studs and leaves more room for insulation, but limits the loads and sheathing you can use. In Europe 600 mm (and 625 mm in Germany) is common; in Japan 455 mm.

Do I count studs at windows and doors?

Yes. Each opening replaces the layout studs inside it with 2 king studs, at least 2 jack studs, a header and cripples. A typical window adds 3–5 pieces compared with a plain wall, plus the header and sill.

What is the difference between a king stud and a jack stud?

A king stud runs full height from bottom plate to top plate beside the opening. A jack (or trimmer) stud is nailed to the king and stops under the header, carrying it. Cripple studs are the short studs above a header or below a window sill.

How much does it cost to frame a wall?

Lumber for a 12 × 8 ft 2×4 wall with double top plate is about 16 studs and three 12-foot plates — roughly $80–$100 at 2026 sample prices, plus sheathing. Enter your yard’s prices in the lumber list to get your own number.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language