Skip to content
Lumber Calculator

Board feet & pricing

Log Board Foot Calculator

Enter each log’s small-end diameter and length to see its board feet under the Doyle, Scribner and International ¼-inch log rules side by side — with the value of the load at your price and the volume in cubic metres.

Updated October 31, 2026Our methodology

Units
Lumber sizes & prices

Inputs

Logs

Diameter measured at

Measure inside the bark. US log rules use the small end; many metric markets measure at mid-length.

Value

Price is quoted by

Mills and buyers state which rule their price uses — Doyle is common in the South and East, Scribner in the West.

/ MBF

Per thousand board feet (MBF) in imperial units, per m³ in metric.

Results

Estimate — check sizes and quantities with your lumber yard.

Results

Doyle, Scribner and International ¼″: three log rules

A log rule estimates how many board feet of lumber a sawmill can cut from a log. It depends on the log's small-end diameter inside the bark (D, in inches) and its length (L, in feet). The three rules used in the United States give quite different answers for the same log:

Doyle:              BF = (D − 4)² × L ÷ 16
International ¼″:   BF = 0.905 × (0.22·D² − 0.71·D) for each 4-ft section,
                    with D growing ½″ per section
Scribner (approx.): BF ≈ (0.79·D² − 2·D − 4) × L ÷ 16
  • Doyle (about 1825) subtracts 4″ for slabs and assumes a 5/16″ saw kerf. It badly underestimates small logs and overestimates very large ones. It is still the most common rule for buying hardwood logs in the South and East.
  • Scribner (about 1846) is a diagram rule: it was made by drawing 1″ boards inside circles of each diameter, with no allowance for taper. Scribner Decimal C is the same rule rounded to the nearest 10 board feet. Because it is a set of drawings, not an equation, this calculator uses a common formula approximation that stays within about 7% of the published table.
  • International ¼″ (1906) assumes a ¼″ kerf and ½″ of taper every 4 ft. It is the most consistent rule and comes closest to the lumber a modern mill actually saws.

Log scale table for 16-foot logs

Board feet in one 16-ft log by small-end diameter, from Virginia Cooperative Extension publication CNRE-201. The calculator reproduces the Doyle column exactly and International ¼″ to within 2%.

DiameterInternational ¼″Scribner Dec CDoyle
8″403016
12″958064
16″180160144
20″290280256
24″425400400
30″675660676
40″1,2201,2001,296

Doyle reads lower than International up to about 30″ and higher above it. On a 12″ log Doyle gives a third less volume than International — which is why sellers of small logs should know which rule a buyer is using.

Worked example: what is my log worth?

A 16″ × 16 ft log:

  • Doyle: (16 − 4)² × 16 ÷ 16 = 144 bd ft
  • International ¼″: four 4-ft sections at 16″, 16½″, 17″ and 17½″ = 199.6 × 0.905 ≈ 180 bd ft
  • Scribner Decimal C: 160 bd ft in the table (the formula gives about 166, rounded to 170)

Log prices are quoted per thousand board feet of a named rule. At $100/MBF the same log is worth $18.00 by International, $16.00 by Scribner or $14.40 by Doyle. A price of $300/MBF Doyle values it at 144 × $0.30 = $43.20. Pick the rule in the calculator that your buyer quotes, enter the price, and the other two rules are shown for comparison.

Prices for sawlogs vary enormously with species, grade, diameter and distance to the mill, so there is no sample price here — ask local mills or your state forestry agency for current prices.

How to measure a log

  1. Diameter: measure across the small end, inside the bark. If the end is oval, average the long and short dimensions. Scalers round down to the whole inch.
  2. Length: measure along the log. Logs are usually bucked to even lengths (8, 10, 12 … 16 ft) plus a few inches of trim allowance, which is not counted.
  3. Long logs: logs over about 20 ft are scaled as two shorter logs, because taper makes the far half fatter than the small end suggests.
  4. Defects: rot, sweep, crook and splits are deducted by the scaler. This calculator gives gross scale — expect the net scale to be lower.

To estimate standing trees, you also need merchantable height and form class; this tool is for logs on the ground. Once the logs are sawn, the board foot calculator tallies the lumber.

Metric: log volume in cubic metres

In Europe and most metric markets, logs are sold by the cubic metre of solid wood (in German, the Festmeter) rather than by a board-foot rule. Volume is usually computed with Huber's formula from the mid-length diameter, or Smalian's formula from both end diameters:

Huber:   V = π/4 × D(mid)² × L
Smalian: V = π/8 × (D(small)² + D(large)²) × L

A 40 cm mid-diameter log, 4 m long, holds π/4 × 0.40² × 4 = 0.503 m³. Choose metric units in the settings menu to enter diameters in cm and lengths in metres and to price per m³; set “Diameter measured at” to mid-length if that is how your logs are measured. Both formulas give the volume of the round log, not the sawn lumber in it.

Frequently asked questions

How many board feet are in a 16-inch log?

A 16″ × 16 ft log scales 144 board feet by Doyle, about 160 by Scribner Decimal C and about 180 by the International ¼″ rule.

What is the Doyle log rule formula?

Board feet = (D − 4)² × L ÷ 16, where D is the small-end diameter inside the bark in inches and L is the log length in feet.

Which log rule is most accurate?

The International ¼″ rule comes closest to the lumber a modern mill actually saws. Doyle underestimates logs under about 30″, so sawmills often get more lumber than the Doyle scale (called overrun).

What is Scribner Decimal C?

The Scribner rule rounded to the nearest 10 board feet, with the last zero dropped — a 16″ × 16 ft log is “16” in Decimal C, meaning 160 board feet. It is widely used in the western US.

How do I calculate the value of a log?

Multiply its board feet by the price per thousand board feet and divide by 1,000 — using the rule the price is quoted in. 144 bd ft Doyle at $300/MBF Doyle is $43.20.

How do I measure log diameter for scaling?

At the small end, inside the bark, rounded down to the whole inch. Average two measurements at right angles if the end is not round.

Related calculators

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language