6 min read
How Much Lumber Do You Need for a 12×16 Deck? Full Material List
A 12×16 attached deck needs 15 joists, a doubled beam, three posts, 28 deck boards and about 12 bags of concrete. Here is the full list line by line, and how each number is worked out.
By the FreeLumberCalculator.com editorial team
A 12 × 16 ft deck is one of the most common sizes people build. At 192 square feet it is big enough for a table and a grill, and small enough to frame with ordinary 2×8 joists and stock-length boards. This guide walks through the complete lumber list for a 12×16 deck attached to the house, explains where each number comes from, and shows how to adjust it for your own design. All the figures come from our deck lumber calculator with its default settings, so you can open it and change any input to see your own list.
The design behind the numbers
Every lumber list depends on a few design choices. This example uses the most common ones for a DIY deck in the US:
- Size: 16 ft along the house and 12 ft out from it.
- Height: about 3 ft from the ground to the top of the deck boards.
- Support at the house: a ledger board bolted to the house rim, so the deck needs only one beam at the outer edge.
- Joists: 2×8 pressure-treated joists at 16″ on center, running away from the house.
- Beam and posts: a doubled 2×10 beam on three 6×6 posts set on concrete footings.
- Decking: 5/4×6 treated deck boards with a 3/16″ gap, running parallel to the house.
Change any of these and the list changes. A freestanding deck needs a second beam, a taller deck needs longer posts, and composite decking usually needs joists at 12″ on center. The calculator handles all of these.
The complete 12×16 deck lumber list
Here is the shopping list, grouped the way you would pick it at the yard. Quantities already include a waste allowance where one makes sense (10% on joists, 7% on deck boards).
| Qty | Item | Used for |
|---|---|---|
| 15 | 2×8 × 12 ft, treated | Joists (13 needed + spares) |
| 2 | 2×8 × 16 ft, treated | Ledger and rim joist |
| 1 + 1 | 2×8 × 8 ft and 10 ft, treated | Mid-span blocking |
| 2 | 2×10 × 16 ft, treated | Doubled beam |
| 1 | 6×6 × 8 ft, treated | Three short posts, cut to length |
| 28 | 5/4×6 × 16 ft deck boards | Decking (26 rows + spares) |
| 12 | 80 lb bags of concrete | Three footings |
| 13 | Joist hangers | Joists at the ledger |
| 13 | Hurricane ties | Joists to beam |
| 3 + 3 | Post bases and post caps | Posts to footing and beam |
| ≈ 710 | Deck screws | Two per board at every joist |
That is about 664 board feet of lumber, weighing close to a ton when it is wet treated wood. At our editable sample prices the whole package comes to about $1,000, or $5.21 per square foot before railings and stairs. Local prices vary a lot, so type in your yard’s prices to get your own total.
How many joists does a 12×16 deck need?
Joists run from the ledger to the rim, across the 12 ft direction, and are spaced along the 16 ft side. The count is the length divided by the spacing, plus one for the end:
16 ft × 12 ÷ 16″ = 12 spaces → 13 joists
Each joist is shorter than 12 ft. The ledger and the rim joist each take 1½″, so the joists themselves are about 11 ft 9 in long and are cut from 12 ft boards. Two spares bring the order to 15. If you set the spacing to 12″ for composite decking, the count rises to 17 joists, and at 24″ it drops to 9, although 24″ spacing is only suitable for some thicker deck boards.
A 2×8 is a common joist size for a 12 ft deep deck because the joists only have to span about 10 ft from the ledger to the beam, with a short cantilever beyond it. Spans depend on species, grade and load, so always check your joist size against the span table in your local code (in the US, IRC Table R507.6).
Beam, posts and footings
With a ledger carrying the house side, a 12 ft deep deck needs one beam near the outer edge. Setting the beam 2 ft in from the edge gives a cantilever that hides the beam and posts under the deck. The beam is two 2×10s nailed together, 16 ft long, so it can be cut from two 16 ft boards with no splice.
Posts are spaced no more than about 8 ft apart, so a 16 ft beam needs three posts: one near each end and one in the middle. On a deck this low, each post is only about 16 inches long, so all three come out of a single 8 ft 6×6. Each footing here is a 12″ round hole 36″ deep, which takes four 80 lb bags of concrete, or twelve bags in total. Footing depth must reach below your local frost line, so ask your building department before you dig.
Deck boards: how many and how long?
This is where most estimates go wrong. A 5/4×6 deck board is really 5½″ wide, and with a 3/16″ gap each row covers about 5.69″. The deck is 12 ft (144″) from the house to the outer edge, so:
rows = (144″ + 3/16″) ÷ (5½″ + 3/16″) = 25.4 → 26 rows
Because the deck is exactly 16 ft long, each row is one 16 ft board, and there are no butt joints at all. That is the main reason 12×16 is such an efficient size. With a 7% allowance for bad boards, you buy 28 deck boards. The last row is ripped down to about 1 13/16″ wide, or you can adjust the gap slightly so the final board stays full width.
If your yard does not stock 16 ft boards, the calculator plans the seams for you. With 8 ft boards only, for example, every row needs a joint, and each joint must land on a joist and be staggered from the rows next to it. The calculator places them for you and shows the pattern on a plan drawing.
How to adjust the list for your deck
- Freestanding deck: no ledger, but a second beam and set of posts next to the house.
- Higher deck: longer posts (often one 8 or 10 ft 6×6 per post), and you will probably need stairs. Use the stair stringer calculator for stringers and treads.
- Diagonal or picture-frame decking: raise the decking allowance to about 15% for 45° boards or 12% for a border, and add blocking under the border.
- Composite boards: joists at 12″ on center and the hidden fasteners or screws the maker specifies.
- Railings: not included here. A railing typically needs posts every 6 ft or less plus top and bottom rails and balusters.
Common mistakes when buying lumber for a deck
- Using nominal width for the decking count. Dividing 144″ by 6″ gives 24 rows, two short of what you need.
- Forgetting the ledger, rim and blocking. They add three or four long boards to the order.
- Buying untreated lumber for framing. Everything in a deck frame should be pressure-treated and rated for its use, with posts rated for ground contact.
- Ignoring concrete and hardware. Concrete, hangers, ties, post bases, caps and screws add about $236 to this deck at sample prices.
- Not planning board lengths. Choosing the wrong stock length can turn zero seams into dozens.
Get your own deck lumber list
Every deck is a little different, so treat this list as a starting point. Open the deck lumber calculator, enter your size, height and materials, and it produces the full list with a 3D model and a board-layout plan. Use “Add to lumber list” to combine it with stairs or a railing, then print it or copy it into a message to your lumber yard. If you want to compare quotes, the lumber cost calculator adds tax and delivery.
Frequently asked questions
How many deck boards do I need for a 12×16 deck?
26 rows of 16 ft 5/4×6 boards with a 3/16″ gap, or 28 boards with a 7% allowance. Running the boards the 16 ft way means no butt joints.
How many joists are in a 12×16 deck?
13 joists at 16″ on center along the 16 ft side, each about 11 ft 9 in long. Buy 15 12 ft boards to allow for culls.
How much does the lumber for a 12×16 deck cost?
About $1,000 for treated lumber, concrete and hardware at our October 2026 sample prices, or roughly $5 per square foot. Composite decking and railings cost extra. Enter your local prices in the calculator for an exact figure.
What size joists do I need for a 12×16 deck?
2×8 joists at 16″ on center are common when a beam sits about 2 ft in from the outer edge, because the joists span only about 10 ft. Check the span table in your local building code for your species and grade.