Skip to content
Lumber Calculator

5 min read

How Much Does a 2×4 Weigh? Lumber Weight Chart by Size and Species

An 8 ft kiln-dried SPF 2×4 weighs about 7.9 lb, a Douglas fir one about 9.9 lb, and a wet pressure-treated one about 14.6 lb. Here is the chart for every common size and how to work out a full load.

By the FreeLumberCalculator.com editorial team

Open the calculatorLumber weight calculator

How much does a 2×4 weigh? An 8 ft kiln-dried spruce-pine-fir 2×4, the stud you find in every big-box store, weighs about 7.9 lb. The same board in Douglas fir weighs about 9.9 lb, in southern yellow pine about 10.7 lb, and fresh from the treating plant as pressure-treated pine about 14.6 lb. The spread is almost 2 to 1, and it matters when you are loading a truck, carrying boards up a ladder or checking a trailer’s rating. This guide gives a weight chart for the common sizes, explains why the numbers vary, and shows how to estimate a whole load with the lumber weight calculator.

How lumber weight is calculated

Weight is simply volume times density, but two details trip people up:

weight = actual thickness × actual width × length × density

2×4 × 8 ft (SPF, kiln-dried):
1.5″ × 3.5″ × 96″ = 504 cu in = 0.292 cu ft
0.292 cu ft × 26.9 lb/cu ft ≈ 7.9 lb
  • Use the actual size, not the nominal size. A 2×4 is really 1½″ × 3½″, so it holds about two-thirds of the wood its name suggests. Board feet are billed on the nominal size, but weight comes from the wood that is actually there. The lumber sizes chart lists nominal and actual dimensions for every size.
  • Density depends on species and moisture. Kiln-dried softwood framing lumber is dried to 19% moisture or less (the KD-19 stamp) and usually ships near 15%. Treated lumber is often sold still wet from the treating process, and green lumber is freshly sawn and full of water.

2×4 weight by species and moisture

Here is an 8 ft 2×4 in the species you are most likely to buy in the US:

Species and conditionDensity used2×4 × 8 ftPer linear foot
Western red cedar, kiln-dried23.7 lb/cu ft6.9 lb0.86 lb
Spruce-pine-fir (SPF), kiln-dried26.9 lb/cu ft7.9 lb0.98 lb
Hem-fir, kiln-dried28.8 lb/cu ft8.4 lb1.05 lb
Douglas fir-larch, kiln-dried34.0 lb/cu ft9.9 lb1.24 lb
Southern yellow pine, kiln-dried36.5 lb/cu ft10.7 lb1.33 lb
SPF, green (freshly sawn)35.0 lb/cu ft10.2 lb1.28 lb
Pressure-treated pine, wet49.9 lb/cu ft14.6 lb1.82 lb

Treated pine loses most of that extra water as it dries in the sun. Once it is dry it weighs about the same as untreated southern yellow pine, roughly 10.7 lb per 8 ft 2×4. Lumber labeled KDAT (kiln-dried after treatment) is sold that way, which is why it is lighter and more stable than regular wet treated stock.

Lumber weight chart: 2×4 to 2×12, 4×4 and 6×6

Weights per piece for common sizes and lengths, kiln-dried except the treated column:

Size and lengthSPFDouglas firSouthern pineTreated, wet
2×4 × 8 ft7.9 lb9.9 lb10.7 lb14.6 lb
2×4 × 10 ft9.8 lb12.4 lb13.3 lb18.2 lb
2×4 × 12 ft11.8 lb14.9 lb16.0 lb21.8 lb
2×4 × 16 ft15.7 lb19.8 lb21.3 lb29.1 lb
2×6 × 8 ft12.3 lb15.6 lb16.7 lb22.9 lb
2×6 × 12 ft18.5 lb23.4 lb25.1 lb34.3 lb
2×6 × 16 ft24.7 lb31.1 lb33.5 lb45.8 lb
2×8 × 12 ft24.4 lb30.8 lb33.1 lb45.3 lb
2×8 × 16 ft32.5 lb41.1 lb44.1 lb60.3 lb
2×10 × 16 ft41.5 lb52.4 lb56.3 lb77.0 lb
2×12 × 16 ft50.5 lb63.7 lb68.5 lb93.6 lb
4×4 × 8 ft18.3 lb23.1 lb24.9 lb34.0 lb
6×6 × 8 ft45.2 lb57.1 lb61.4 lb83.9 lb
5/4×6 deck board × 16 ft16.5 lb20.8 lb22.3 lb30.5 lb
1×6 fence picket × 6 ft4.6 lb5.8 lb6.3 lb8.6 lb

Real boards vary by about 10–15% either way with moisture, growth rate and how much dense latewood they contain, so two 2×4s from the same stack can differ by a pound. Use the chart for planning loads, not for anything structural.

Why a wet treated board weighs so much more

Pressure treatment forces a water-based preservative deep into the wood. The board leaves the plant carrying a lot of that water, which is why a treated 2×12 × 16 ft can approach 94 lb while the same size in kiln-dried SPF is about 50 lb. That has two practical effects. First, a deck or fence package is far heavier than its board-foot total suggests. Second, the boards shrink as they dry, so deck boards and fence pickets installed tight will open small gaps over the first season.

How much lumber fits in a pickup or trailer?

A common rule of thumb puts a half-ton pickup’s payload at 1,000–1,500 lb, but your truck’s real figure is on the sticker in the driver’s door jamb, and it includes passengers and anything else in the bed. At 1,500 lb, that is about:

  • 191 kiln-dried SPF 2×4 × 8 ft studs, or 121 SPF 2×6 × 8 ft;
  • 102 wet treated 2×4 × 8 ft;
  • 49 wet treated 5/4×6 × 16 ft deck boards;
  • 33 wet treated 2×8 × 12 ft joists.

Whole projects add up quickly. The lumber, concrete aside, for the 12×16 deck weighs about 1,960 lb, a 100 ft 6 ft privacy fence about 3,000 lb, and a 24×24 garage package with rafters and OSB sheathing about 6,300 lb. Any of these is more than one pickup load, and the garage is a job for yard delivery. For a trailer, check both its rating and your vehicle’s towing and tongue-weight limits, and remember that long boards hanging out the back need a flag and proper tie-downs.

Estimate the weight of your whole order

Instead of adding up chart rows, enter your list in the lumber weight calculator: pick the species and moisture, add a row for each size, length and quantity, and it gives the total weight, the weight per piece and per foot, and the share of a typical pickup payload. If you already have a material list from one of our project calculators, the weight shows up in its totals too, and the lumber calculator combines several lists into one order. To see how the same order translates into board feet for pricing, use the board foot calculator.

Frequently asked questions

How much does a 2×4×8 weigh?

About 7.9 lb in kiln-dried spruce-pine-fir, 9.9 lb in Douglas fir, 10.7 lb in southern yellow pine and about 14.6 lb as wet pressure-treated pine. Individual boards vary by 10–15%.

How much does a pressure-treated 2×4 weigh?

Fresh from the plant, about 1.8 lb per foot, or 14.6 lb for an 8 ft board. After it dries out, it weighs about the same as untreated southern yellow pine, roughly 10.7 lb for 8 ft.

How many 2×4s can a half-ton pickup carry?

At a 1,500 lb payload, about 191 kiln-dried SPF 2×4 × 8 ft or about 102 wet treated ones. Check the payload sticker on your door jamb and subtract passengers and tools.

How much does a 2×6 weigh?

An 8 ft kiln-dried SPF 2×6 weighs about 12.3 lb, a 12 ft one about 18.5 lb and a 16 ft one about 24.7 lb. Wet treated, a 2×6 × 16 ft is about 45.8 lb.

Calculators used in this article

More from the blog

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language