Skip to content
Lumber Calculator

4 min read

How Much Lumber Does It Take to Frame a House? Board Feet per Square Foot

A simple 2,000 sq ft single-story house on a slab takes roughly 9,400 board feet of framing lumber and about 146 sheets of sheathing. Here is how that number is built up, and what makes it go up or down.

By the FreeLumberCalculator.com editorial team

Open the calculatorHouse lumber calculator

When you are budgeting a new house or an addition, one of the first questions is how much framing lumber it will take. Builders often answer with a rule of thumb in board feet per square foot, but those rules hide a lot: the number of stories, the floor system, the roof and the wall layout all change the result. This article builds the estimate up from the framing itself, using our house lumber calculator, so you can see where the lumber goes and adjust it for your plans.

The short answer

For a simple rectangular house with 8 ft walls, a 6/12 stick-framed gable roof and typical interior walls, our model gives:

HouseBoard feetPer sq ftSheetsLumber cost*
1,500 sq ft, 1 story, slab≈ 7,6005.0119≈ $7,900 ($5.27/sq ft)
2,000 sq ft, 1 story, slab≈ 9,4004.7146≈ $9,800 ($4.89/sq ft)
2,500 sq ft, 1 story, slab≈ 10,6004.2170≈ $11,100 ($4.44/sq ft)
2,000 sq ft, 2 stories, slab≈ 10,5005.3153≈ $11,500 ($5.73/sq ft)
2,000 sq ft, 1 story, framed floor≈ 12,9006.5214≈ $14,900 ($7.44/sq ft)

*Framing lumber and wall and roof sheathing at our editable October 2026 sample prices. Not included: foundation, beams and posts, stairs, trusses or engineered lumber, blocking, trim, siding, roofing and fasteners.

So a rough range of 4 to 7 board feet per square foot covers most simple houses, with smaller and more complex houses at the top of the range. Treat it as a budgeting figure, not an order.

How the estimate is built

Rather than multiplying the floor area by a constant, the calculator frames a simplified version of the house:

  1. Footprint. The floor area per story is turned into a rectangle using the length-to-width ratio you choose. A 2,000 sq ft single-story house at the default 1.6 ratio becomes a box of about 56½ × 35⅓ ft.
  2. Exterior walls. 2×6 walls at 16″ on center around the perimeter, with corners, windows and doors framed with king and jack studs, headers and cripples, plus a double top plate.
  3. Interior walls. 2×4 partitions modelled as cross walls whose total length is a share of the perimeter, with extra studs where they meet the exterior walls.
  4. Floors. Either a slab (treated bottom plates, no floor framing) or framed floors with joists spanning to a center beam.
  5. Roof. A stick-framed gable roof with rafters, ridge, collar ties, ceiling joists and fascia.
  6. Sheathing. Wall and roof sheathing (and subfloor for framed floors) in 4×8 sheets.

Each part is counted with the same layout rules as the individual framing calculators, so the total is a sum of real members rather than an average.

Where the lumber goes

In the 2,000 sq ft single-story example, the biggest shares are:

  • The roof. About 204 rafters, 88 ceiling joists, collar ties, the ridge and fascia, plus 87 sheets of roof sheathing. Roof framing and sheathing make up more than half of the lumber cost in this model.
  • Exterior walls. About 154 pre-cut 2×6 studs, plates, headers and 59 sheets of wall sheathing.
  • Interior walls. About 165 pre-cut 2×4 studs plus plates and headers.

That is why a single-story house uses less lumber per square foot as it gets bigger: the perimeter grows more slowly than the area. A two-story house of the same area has half the roof, but it adds a framed floor between the stories and more wall area, so in this model it ends up using more lumber, not less.

What makes the number go up

  • Framed floors instead of a slab. Joists, rims, beams and subfloor add more than 3,500 board feet and about 70 sheets to the 2,000 sq ft example.
  • A complicated shape. Every corner, bump-out, hip and valley adds lumber the simple box leaves out.
  • Taller walls. 9 or 10 ft walls need longer studs and more sheathing.
  • Lots of openings. More windows and doors mean more headers, kings, jacks and cripples.
  • Attached garage, porches and decks. Estimate these separately with the garage lumber calculator and the deck lumber calculator.

What makes it go down

  • Roof trusses replace rafters and ceiling joists with factory-built trusses. You still buy them, but as engineered components rather than lumber.
  • Advanced framing (24″ on center where allowed, two-stud corners, single top plates where permitted) saves studs and plates.
  • A simple rectangle keeps the perimeter, corners and roof as small as possible for the floor area.

From estimate to order

A square-foot estimate is good for budgets and for checking a builder’s quote. Before you order, you need a takeoff from the actual plans. Use the framing lumber calculator to list every wall with its openings, the rafter calculator for the roof, and the plywood and sheathing calculator for sheets. Add each list to your lumber list and you have one order to price with your supplier. Structural sizes, such as beams, headers, joists and rafters, must come from your building code’s span tables or an engineer.

Estimate your house

Open the house lumber calculator, enter the floor area, stories, wall height, floor system and roof pitch, and set your local price per MBF. It shows board feet, sheets, cost per square foot and a plan of the framed box, so you can see what changes when you adjust the design.

Frequently asked questions

How many board feet of lumber are in a 2,000 sq ft house?

Our model gives about 9,400 board feet for a simple single-story 2,000 sq ft house on a slab, about 4.7 board feet per square foot. A framed floor raises it to about 12,900.

How much does framing lumber cost per square foot?

About $4.40 to $7.50 per square foot for framing lumber and sheathing in our examples, at October 2026 sample prices. Your local prices, the floor system and the house’s shape change this a lot.

Does a two-story house use less lumber?

Not necessarily less lumber, but less per square foot of roof and foundation. In our model a 2,000 sq ft two-story house uses about 10,500 board feet, more than the single-story version on a slab, because it adds a floor system and more wall area.

Is the house lumber calculator a substitute for a takeoff?

No. It is a ballpark estimate for budgeting. For an order, do a takeoff from your plans wall by wall and check structural sizes against your local code.

Calculators used in this article

More from the blog

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language