Skip to content
Lumber Calculator

5 min read

Lumber List for a 10×12 Shed: Every Board, Sheet and Cost

A 10×12 gable shed on skids takes about 108 pieces of lumber and 28 sheets, roughly 850 board feet. Here is the full material list by floor, walls and roof, and where the money goes.

By the FreeLumberCalculator.com editorial team

Open the calculatorShed lumber calculator

A 10 × 12 ft shed is the size most people picture when they think of a backyard storage shed. It holds a mower, bikes and garden tools with room to work. Many towns also allow sheds of around this size with a simpler permit process, though the rules vary widely, so check locally. This article gives a complete lumber list for a 10×12 gable shed built on skids, broken down by floor, walls, gables and roof, with the reasoning for each quantity. The numbers come from our shed lumber calculator, so you can change the size, roof or siding and get an updated list in seconds.

The shed this list is for

  • Footprint: 10 ft wide (the roof spans this way) by 12 ft long (along the ridge).
  • Floor: three 4×6 treated skids, 2×6 floor joists at 16″ on center, and 23/32″ tongue-and-groove subfloor.
  • Walls: 8 ft walls of 2×4 studs at 16″ on center with 92⅝″ pre-cut studs, a double top plate and three-stud corners, a door in the long front wall and one window.
  • Roof: a 6/12 gable roof with 2×6 rafters at 24″ on center, a 12″ eave overhang, a 6″ rake overhang, a 2×8 ridge board, collar ties and fascia.
  • Cladding: T1-11 panel siding, which doubles as wall sheathing, and 7/16″ OSB roof sheathing.

Floor: skids, joists and subfloor

A shed floor on skids works like a small deck sitting on three treated beams. The skids run the 12 ft length, and the joists span across the 10 ft width, spaced along the 12 ft side:

12 ft × 12 ÷ 16″ = 9 spaces → 10 joists (+1 spare = 11)
QtyItemUsed for
34×6 × 12 ft, treatedSkids
112×6 × 10 ftFloor joists
22×6 × 12 ftRim joists
523/32″ T&G subfloor sheets, 4×8Floor deck

The floor is 120 sq ft, or 3¾ sheets of 4×8. Laying the rows continuously and starting each row with the previous offcut gets it down to four sheets; the fifth is a spare. Because the floor sits close to the ground, use treated lumber for the skids at least, and ideally for the whole floor frame.

Walls: studs, plates and headers

The front and back walls run the full 12 ft, and the two side walls fit between them, so they are about 9 ft 5 in long. At 16″ on center, a 12 ft wall needs 10 layout studs and a 9 ft 5 in wall needs 8. The corners, the door and the window add more:

  • Corners: two extra studs at each end of the through walls form solid three-stud corners for nailing siding and drywall.
  • Door and window: each opening gets two king studs, jack studs under the header, cripples above it and, for the window, a rough sill with cripples below.
QtyItemUsed for
482×4 × 92⅝″ pre-cut studsFull-height studs, corners and kings (incl. waste)
52×4, mixed 8–18 ftJacks, cripples and blocking, cut from stock
42×4 × 12 ft and 10 ftBottom plates
62×4 × 12 ft and 20 ftDouble top plates
22×8 × 10 ft and 8 ftDoor and window headers
12×4 × 8 ftWindow rough sill

Pre-cut 92⅝″ studs plus three 1½″ plates give a wall about 97⅛″ tall, which is the standard “8 ft” wall. If your shed sits on a concrete slab instead of skids, the bottom plates must be pressure-treated.

Gables and roof

A 6/12 pitch rises 6 inches for every 12 inches of run. Half the 10 ft span is a 5 ft run, so the roof peak sits about 2½ ft above the top plates. Each common rafter is about 81 inches long before cutting, including the 12″ overhang, so an 8 ft 2×6 is enough with room for the plumb and tail cuts.

rafters per side = 12 ft × 12 ÷ 24″ + 1 = 7, plus a fly rafter at each rake
→ 9 per side, 18 in total (20 with spares)
QtyItemUsed for
202×6 × 8 ftRafters, including fly rafters
12×8 × 14 ftRidge board (one size deeper than the rafters)
12×6 × 16 ftCollar ties, cut into pieces
22×6 × 14 ftFascia
22×4 × 8 ft and 18 ftGable-end studs
97/16″ OSB, 4×8Roof sheathing

Siding and totals

T1-11 siding covers the four walls and the two gable triangles. It is the single biggest line on the list: 14 sheets account for about $730 of the total at sample prices. Cheaper options are OSB sheathing with lap siding, or plain plywood that you paint.

Altogether the shed comes to about 108 pieces of lumber and 28 sheets: roughly 850 board feet and more than 3,000 lb of material. At our sample prices that is about $1,790, or close to $15 per square foot of floor. The list does not include roofing, trim, the door itself, the window, fasteners or paint.

Ways to cut the cost of a 10×12 shed

  1. Change the siding. Siding is about 40% of this list. Compare T1-11 with OSB plus lap siding, or board-and-batten.
  2. Frame the walls at 24″ on center. Where your local rules and siding allow it, this saves about a fifth of the studs.
  3. Don’t assume a lean-to roof is cheaper. A single-slope roof needs no ridge or collar ties, but on a 10 ft wide shed the tall back wall needs longer studs and more siding. In the calculator the lean-to version costs about $1,990 against $1,790 for the gable, so compare both before you decide.
  4. Buy to the cut. Plates and blocking can often share boards. The cut list optimizer shows the cheapest mix of lengths.

Make the list for your shed

Open the shed lumber calculator and pick a size such as 8×10, 10×12 or 12×16, then set the roof style, door, windows and floor. It frames the whole building in 3D and gives you a list grouped by floor, walls, gables, roof and sheathing. For bigger outbuildings, the framing lumber calculator takes any list of walls, and the plywood calculator counts sheathing on its own.

Frequently asked questions

How many 2×4s do I need for a 10×12 shed?

About 48 pre-cut 92⅝″ studs for 8 ft walls at 16″ on center, including corners, king studs and spares, plus about 18 more 2×4s for plates, jacks, cripples, sills and gable studs.

How much does the lumber for a 10×12 shed cost?

Roughly $1,800 for framing, sheathing and T1-11 siding at our October 2026 sample prices, or about $15 per square foot of floor. Roofing, the door, windows and fasteners are extra.

How many sheets of plywood for a 10×12 shed?

About 28: 5 sheets of subfloor, 9 sheets of roof sheathing and 14 sheets of T1-11 siding for the walls and gables, including a few spares.

What size rafters for a 10×12 shed?

2×6 rafters at 24″ on center are common for a 10 ft span with a 6/12 pitch, at about 81 inches long including the overhang. Check rafter spans for your snow load in your local code.

Calculators used in this article

More from the blog

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language