Skip to content
Lumber Calculator

5 min read

How to Calculate Board Feet for Hardwood: 4/4, 5/4 and 8/4 Explained

Hardwood is tallied on its rough thickness in quarters (4/4 = 1″), its actual width and its length in feet. Here is the formula, a worked tally of a mixed stack, and how much extra to buy for waste.

By the FreeLumberCalculator.com editorial team

Open the calculatorBoard foot calculator

Buying hardwood is different from buying 2×4s. There are no fixed widths, the boards are often rough, thickness is given in odd-looking fractions like 4/4 and 8/4, and the price is per board foot rather than per piece. Once you know how a dealer tallies a board, though, the math takes a few seconds. This guide shows how to calculate board feet for hardwood, works through a real mixed stack, and explains how much extra to buy so you do not run short halfway through a project. You can check every number with the board foot calculator.

The board foot formula for hardwood

A board foot is a volume of wood 1″ thick, 12″ wide and 12″ long, or 144 cubic inches. The formula is the same as for softwood:

board feet = thickness (in) × width (in) × length (ft) ÷ 12

What changes is which dimensions you plug in:

  • Thickness: the rough thickness in quarters of an inch, even if the board has been planed thinner.
  • Width: the actual measured width, because hardwood comes in random widths. Measure at the narrowest point that is still full thickness and ignore wane.
  • Length: the length in feet. Dealers usually round down to the whole foot or half foot; ask how yours tallies.

Softwood dimension lumber is billed on its nominal size instead (a 2×4 counts as 2″ × 4″), which is why you should not mix the two methods.

What 4/4, 5/4 and 8/4 mean

Hardwood thickness is stated in quarters of an inch, said as “four-quarter”, “five-quarter” and so on:

Quarter sizeRough thicknessBoard feet in a 6″ × 8 ft board
4/41″4.0
5/41¼″5.0
6/41½″6.0
8/42″8.0
12/43″12.0

The quarter size is the thickness as sawn. A 4/4 board planed smooth on both faces finishes at about 13/16″, but it is still tallied as 1″. In other words, you pay for the wood that ends up as shavings, so it is worth knowing which parts of a project really need thick stock.

Worked example: tallying a mixed stack of 4/4 oak

Say you pick six rough 4/4 red oak boards from the rack. Measure each one and run the formula:

BoardWidthLengthBoard feet
15¼″8 ft3.50
26½″8 ft4.33
37″9 ft5.25
48¾″10 ft7.29
56″10 ft5.00
64½″8 ft3.00
Total28.38

At our editable sample price for hardwood of $4.50 per board foot, the stack costs about $127.69. A single 8/4 board 8″ wide and 8 ft long is 2 × 8 × 8 ÷ 12 = 10.67 board feet, or $48.00 at the same rate, although thick stock often sells at a higher price per board foot than 4/4. Species, grade and region move hardwood prices a lot, so type in your dealer’s figures.

Entering every board by hand gets tedious on a big stack. In the board foot calculator add one row per board, or one row per group of identical boards, and it totals the board feet, cubic volume, linear feet and cost.

Rough, surfaced and per-linear-foot pricing

Hardwood is sold in a few forms, and they are not priced the same way:

  • Rough sawn: the cheapest per board foot and what most hardwood dealers stock. You need a jointer and planer, or the dealer’s milling service, to use it.
  • Surfaced two sides (S2S): planed on both faces, still with rough edges. Usually still tallied on the rough thickness.
  • Surfaced four sides (S4S): fully milled boards in fixed widths, the kind home centers sell. These are often priced per piece or per linear foot, which hides how much you are paying per board foot.

To compare a per-foot price with a per-board-foot price, convert it. A 4/4 × 6″ board contains 0.5 board feet per linear foot, so $3.00 per linear foot is $6.00 per board foot. The board feet to linear feet converter does this for any size, in both directions.

How much extra hardwood to buy

A cut list tells you the board feet in the finished parts; the lumber you buy has to be larger. You lose wood to planing, to ripping off rough edges, to cutting around knots, checks and sapwood, and to end trims where the boards are split. A common rule of thumb is to add about 20–30% to the board feet of the finished parts, more for lower grades, short parts or carefully matched grain:

finished parts: 24 bd ft
buy: 24 × 1.25 = 30 bd ft  to  24 × 1.30 ≈ 31 bd ft

Grade matters as well. The top hardwood grades (FAS and Select) give long, wide, clear cuttings; Common grades cost less but have more defects between the clear sections. For small parts, a cheaper grade can yield just as well. Buy all the wood for one piece of furniture at once if you can, so the color and figure match.

Board feet in a log

If you are buying logs or having your own trees sawn, board feet are estimated from the small-end diameter and the length with a log rule. The three US rules give very different answers for the same log. For a log 16″ in diameter and 12 ft long:

Log ruleBoard feet
Doyle108
Scribner Decimal C120
International ¼″130

Doyle underestimates small logs heavily, which is why buyers like it and sellers do not. Always agree on the rule before you agree on a price. The log board foot calculator runs all three rules for a whole load of logs.

Prices per MBF and metric volumes

Sawmills and wholesalers quote hardwood per thousand board feet (MBF). Divide by 1,000 to get the price per board foot: $4,500 per MBF is $4.50 per board foot. The MBF calculator converts a per-thousand price to a price per board, and our guide to lumber price per thousand board feet walks through it step by step. If you are importing wood or reading a European price list, one board foot is about 0.00236 m³, so one cubic meter is about 424 board feet.

Frequently asked questions

How do you calculate board feet for 4/4 hardwood?

Multiply 1″ (the 4/4 thickness) by the actual width in inches and the length in feet, then divide by 12. A 4/4 board 6″ wide and 8 ft long is 1 × 6 × 8 ÷ 12 = 4 board feet.

Do you calculate board feet before or after planing?

Before. Hardwood is tallied on its rough thickness, so a 4/4 board planed to about 13/16″ still counts as 1″ thick. Width is the actual measured width.

How many board feet are in an 8/4 board?

Twice as many as a 4/4 board of the same width and length. An 8/4 board 8″ wide and 8 ft long is 2 × 8 × 8 ÷ 12 = 10.67 board feet.

How much extra hardwood should I buy for waste?

A common rule of thumb is 20–30% more than the board feet in the finished parts, and more for lower grades, short parts or matched grain.

Calculators used in this article

More from the blog

Tools

Projects

Framing

Board feet & pricing

Planning

All calculators

Site

Settings

Units

Lumber sizes & prices

Choose the market whose sizes, stock lengths and sample prices you want.

Theme

Language